Fusion
Susan G. Komen Breast Cancer Foundation
Vista Video
Vista Systems
Stran Brand Services
ShowGo
Vista
Cubicle X-Ray Vision
Drop-In
Resource CenterPrintable version Printable Version

Welcome to the Resource Center. Here you will find information on our entire product line.

Fastener Descriptions Ordering & Shipping FAQ A.D.A. Regulations A.D.A. Instructions Other Links

Velcro - Paired Hook & Loop
Pairing Hook and Loop adhesive backed Velcro works best on stable, rigid, flat, clean vertical or horizontal surfaces. This fastener works best for situations where permanent interior signs require occasional removal. Once the adhesive cures (approximately 24 hours) it will become difficult to remove and may lift paint or papered surfaces if pried from the wall. Typically The "hook" or rigid strip of Velcro is adhered to the sign and the "loop" strip of Velcro is adhered to the surface the signs will be attached to. Be sure placement is measured correctly prior to installation. It is advisable to thoroughly wipe down surfaces prior to installation. Surfaces must be dry.

Velcro - Hook Only
Velcro works best on fabric surfaces with sufficient looped or twisted pile, such as cubicle walls. Hook adhesive backed Velcro fasteners is suited for situations where permanent interior signs require occasional removal or where walls are fabric covered. Once the adhesive cures (approximately 12-24 hours) it will become difficult to adjust or remove and may lift paint or papered surfaces if pried from the wall. Typically The "hook" or rigid strip of Velcro is adhered to the sign and the "loop" strip of Velcro is adhered to the surface the signs will be attached to.

High-grade Double-sided Adhesive Tape
High-grade Double-sided Adhesive Tape works best on stable, rigid, flat, clean vertical or horizontal surfaces. This fastener works best for situations where interior signs require permanent installation. Once the adhesive cures (approximately 12-24 hours) it will become difficult to adjust or remove and may lift paint or papered surfaces if pried from the wall. Be sure placement is measured correctly prior to installation. It is advisable to thoroughly wipe down surfaces prior to installation. Surface must be dry.

Cubicle Pins
Cubicle Pins work best on fabric faced hollow partition wall surfaces such as cubicle walls and dividers. Cubicle pin fasteners are suited for situations where permanent interior signs require occasional removal or where walls are covered with fabric too fine for Velcro to attach.

VHB Ultra Double-sided Adhesive Tape
VHB Ultra Double-sided Adhesive Tape works best on stable, rigid, flat, clean vertical or horizontal surfaces. This fastener works best for situations where interior and exterior signs require permanent installation. Once the adhesive cures (approximately 12-24 hours) it will become virtually impossible to adjust or remove and will damage any surface if pried from the wall. Be sure placement is measured correctly prior to installation. It is advisable to thoroughly wipe down surfaces prior to installation. Surface must be dry.

Mounting Holes
Screws work best on stable, rigid, flat, vertical or horizontal surfaces. This fastener works best for situations where interior and exterior signs require permanent installation. However, when using screws only, removal for relocation will result in less damage to surfaces than double-sided tape or Velcro adhesive. Be sure placement is measured correctly prior to installation. Consult a building specialist in your area who will assist with hardware and or anchor selection best suited for the attachment process. EGS provides the holes only. Mounting hardware is not included.

Mounting Hole plus DS Tape Tabs
The combination of Screws and DS Tape works best on stable, rigid, flat, vertical or horizontal surfaces. This fastening combination works best for situations where interior and exterior signs require permanent installation. However, removal for relocation will result in less damage to surface than double-sided tape or Velcro adhesive. Be sure placement is measured correctly prior to installation. Consult a building specialist in your area who will assist with hardware and or anchor selection best suited for the attachment process. EGS provides the holes only. Mounting hardware is not included. This combination of fasteners is best used when screwing too many holes in a surface is prohibitive. Minimal surface damage may still be present upon removal.

     
     

My Account   |   Shopping cart   |   Checkout   |   Site Search   |   Contact Us   |   Create An Account   |   Customer Login   |   Privacy Policy   |   Samples Policy